AWG to mm² Cross-Section & NEC 310.16 Ampacity Derating Calculator
Cross-reference American Wire Gauge (ASTM B258) to metric IEC 60228 mm², 20°C resistance, and NEC 310.15 ambient + raceway bundling derating.
Exact ASTM B258 AWG/kcmil to IEC 60228 Metric Cross-Section Mapping
Multinational machinery builders, UL 508A panel shops, and EPC contractors routinely translate North American drawings specified in AWG and kcmil into metric IEC 60228 / DIN VDE 0298-4 standard cable cross-sections (1.5, 2.5, 4, 6, 10, 16, 25, 35, 50, 70, 95, 120, 185, and 240 mm²). Because logarithmic AWG steps follow D_n = 0.005 × 92^((36−n)/39) inches, exact copper area rarely lands on an integer square millimeter.
When substituting metric cable onto UL/NEC schedules (or vice versa), engineers must select the next larger standard cross-section—for instance replacing 12 AWG (3.31 mm²) with 4 mm², 10 AWG (5.26 mm²) with 6 mm², or 6 AWG (13.3 mm²) with 16 mm²—unless thermal ampacity and short-circuit withstand calculations explicitly validate a smaller size.
Applying NEC 310.16, 90°C Derating Headroom & 240.4(D) Small-Conductor Caps
NEC 110.14(C) permits starting ampacity derating from the 90°C column of Table 310.16 when using 90°C-rated conductors such as THHN, THWN-2, or XHHW-2, provided the final derated ampacity does not exceed the 75°C column limit of the connected circuit breaker and equipment lugs. For example, six 12 AWG THHN copper conductors in a 35°C conduit start at 30 A × 0.96 × 0.80 = 23.04 A, which remains above 20 A.
However, NEC 240.4(D) imposes a strict overcurrent protection ceiling on general branch-circuit small conductors: 15 A max for 14 AWG copper, 20 A max for 12 AWG copper, and 30 A max for 10 AWG copper (except specific motor, HVAC, or welder circuits covered in Table 240.4(G)).
Reference Benchmark & Formula Specification
Deterministic formula: I_derated = I_base(Table 310.16) × K_temp(310.15(B)(1)) × K_bundle(310.15(C)(1))
| Architecture / Standard Tier | Specification | Scope / Operating Range | Reference Benchmark |
|---|---|---|---|
| 12 AWG <-> 4 mm² IEC | Exact 3.31 mm² (6.53 kcmil) | 20 A (60°C) / 25 A (75°C) / 30 A (90°C) | NEC 240.4(D) Max 20 A OCPD |
| 10 AWG <-> 6 mm² IEC | Exact 5.26 mm² (10.38 kcmil) | 30 A (60°C) / 35 A (75°C) / 40 A (90°C) | NEC 240.4(D) Max 30 A OCPD |
| 6 AWG <-> 16 mm² IEC | Exact 13.30 mm² (26.24 kcmil) | 55 A (60°C) / 65 A (75°C) / 75 A (90°C) | 65 A @ 75°C Breaker Lugs |
| 1/0 AWG <-> 50 mm² IEC | Exact 53.49 mm² (105.6 kcmil) | 125 A (60°C) / 150 A (75°C) / 170 A (90°C) | 150 A @ 75°C Breaker Lugs |
Frequently Asked Questions
Can I replace 12 AWG wire with 2.5 mm² metric cable on a 20A NEC circuit?
No on UL/NEC 20A circuits: 2.5 mm² is smaller than 12 AWG (3.31 mm²) and sits closer to 13–14 AWG. On UL 508A / NEC equipment, step up to 4 mm² to exceed 12 AWG cross-section, whereas on IEC/VDE 16A–20A circuits 2.5 mm² is rated per DIN VDE 0298-4 installation method.
Why can I derate from the 90°C column if my breaker lugs are rated 75°C?
Ambient heat and bundled conductors raise mid-run conduit temperature away from the panelboard. NEC 110.14(C) allows using 90°C insulation capacity to absorb mid-conduit thermal derating as long as actual load current never exceeds the 75°C terminal rating at the ends.
Does the green/bare equipment grounding conductor count toward bundling?
No. Under NEC 310.15(E) and 310.15(C)(1), equipment grounding conductors and balanced 3-phase wye neutrals carrying only unbalanced current (unless harmonic-rich nonlinear loads >50%) do not count as current-carrying conductors.