Three-Phase & Single-Phase Voltage Drop Calculator (NEC / IEC)

Evaluate true AC impedance voltage drop across 75°C copper or aluminum feeders in feet or meters against NEC 210.19 (<=3% branch / <=5% total) limits.

Examples:
A
ft
Distance Unit
Conductor Metal (75°C)
cos φ
Advisory Voltage Drop Target
Voltage Drop (V / %)
Steady-State AC Impedance Estimate
6.39 V (1.33%)
6.39 V (1.33%) | 473.6 V @ Load | ADVISORY — <= 3% Target (NEC Note)
Load Voltage & 75°C Cap
473.6 V (85 A max)
Advisory / Thermal Status
ADVISORY — <= 3% Target (NEC Note)
Min <=3% & Ampacity Wire
4 AWG (IEC >= 25 mm²)
Steady-state 60 Hz steel-conduit AC impedance model (NEC Ch. 9 Table 9). NEC 210.19(A) / 215.2(A) 3% branch and 5% total drop figures are Informational Notes (advisory efficiency guidance), not mandatory code prohibitions except under NEC 695.7 (Fire Pumps), 647.4(D), or state energy codes.
Conductor GaugeDrop (V)Drop (%)Advisory / Ampacity Status
6 AWG (IEC >= 16 mm²)9.80 V2.04 %THERMAL OVERLOAD > 65 A (75°C)
4 AWG (IEC >= 25 mm²)6.39 V1.33 %ADVISORY — <= 3% Target (NEC Note)
3 AWG (IEC >= 35 mm²)5.24 V1.09 %ADVISORY — <= 3% Target (NEC Note)
2 AWG (IEC >= 35 mm²)4.30 V0.90 %ADVISORY — <= 3% Target (NEC Note)
How It Was Calculated (Live Substituted Steps)
  1. 1. Effective AC Impedance (Z_eff — 60 Hz Steel Conduit) 0.9497 Ω/km
    Zeff=Rcosφ+XLsinφZ_{\text{eff}} = R\cos\varphi + X_L\sin\varphi → NEC Ch.9 Table 9 (CU @ PF 0.85)
  2. 2. One-Way Steady-State Voltage Drop (ΔV) 6.39 V (1.33%)
    ΔV=3⋅(I/Nsets)⋅Lm⋅Zeff1000\Delta V = \tfrac{\sqrt{3} \cdot (I / N_{\text{sets}}) \cdot L_{\text{m}} \cdot Z_{\text{eff}}}{1000} → (1.732 × 85.0 A × 45.7 m × 0.9497) / 1000
  3. 3. Load Terminal Voltage & NEC 310.16 Thermal Check 473.6 V @ Load (ADVISORY — <= 3% Target (NEC Note))
    Vload=Vsys−ΔV|I≤Nsets⋅I75∘CV_{\text{load}} = V_{\text{sys}} - \Delta V \;\mid\; I \le N_{\text{sets}} \cdot I_{75^\circ\text{C}} → 480 V − 6.39 V | 85 A vs 85 A
Formula
ΔV=K⋅I⋅Lm(R75∘Ccosφ+XLsinφ)1000⋅Nsets\Delta V = \frac{K \cdot I \cdot L_{\text{m}} \left(R_{75^\circ\text{C}}\cos\varphi + X_L\sin\varphi\right)}{1000 \cdot N_{\text{sets}}}K=3(3ϕ),2(1ϕ)K = \sqrt{3}\;\text{(3}\phi\text{)},\; 2\;\text{(1}\phi\text{)}%ΔV=100⋅ΔVVsys\%\Delta V = \frac{100 \cdot \Delta V}{V_{\text{sys}}}
Reviewed against NFPA 70 (NEC 2023) & IEC 60364 • Verified 2026-11-18 Preliminary engineering estimation only; final stamped drawings and protective device coordination must be verified by a licensed Professional Engineer (PE) and local AHJ. View Full 11-Tool Standards & Golden Test Matrix →

Why NEC Chapter 9 Table 9 AC Impedance Beats Simplified K-Factor Formulas

Many basic wire calculators rely on DC circular-mil approximations (Vd = 2·K·I·L / CM) that ignore skin effect, magnetic conduit eddy losses, and inductive reactance (X_L). On conductors 1/0 AWG (53.5 mm², IEC >= 70 mm²) and larger feeding induction motors or VFDs at 0.80–0.85 power factor, inductive reactance in steel conduit contributes 25% to 55% of total voltage drop.

kVACalc models effective AC impedance using NEC Chapter 9 Table 9 values at 75°C in steel raceway: Z_eff = R_AC·cos(φ) + X_L·sin(φ), multiplied by √3 (1.732) for balanced three-phase runs or 2 for single-phase two-wire circuits. You also get an automatic recommendation for the smallest conductor that simultaneously satisfies thermal ampacity and the 3% branch drop ceiling.

NEC 210.19, IEC 60364-5-52, DIN VDE 0100-520 & NBR 5410 Compliance Ceilings

Across North American and international electrical codes—including NEC 210.19(A) Informative Note No. 4 and 215.2(A)(1), Mexican NOM-001-SEDE, IEC 60364-5-52 Table G.52.1, DIN VDE 0100-520, and ABNT NBR 5410—engineering practice limits branch-circuit drop to 3% and combined feeder-plus-branch drop to 5% on public utility supplies.

Keeping steady-state drop below 3% prevents induction motor locked-rotor torque degradation (starting torque scales with the square of terminal voltage, V²), eliminates contactor coil chatter on 120V/230V control circuits, and avoids nuisance DC-bus undervoltage faults on industrial variable frequency drives.

Engineering Scope, Standards Edition & Model Limitations

Steady-State AC Impedance Estimate Formula v2.1.0 Reviewed 2026-11-18 View Full 11-Tool Standards & Golden Test Matrix →
Referenced Code Editions & Clauses Edition Applicable Clauses & Engineering Scope
NFPA 70 (NEC) 2023 Edition Art. 210.19(A) Info Note 4 & 215.2(A)(1) Info Note 2 (3% Branch / 5% Total Advisory), Ch. 9 Table 9, Table 310.16
IEC 60364-5-52 / ASHRAE 90.1 2009 / 2022 Maximum voltage-drop planning limits and energy-code feeder drop caps

Mathematical Model Assumptions

  • Uses NEC Chapter 9 Table 9 effective AC resistance (75°C) and 60 Hz inductive reactance in magnetic steel conduit: Z_eff = R cos φ + X sin φ.
  • Parallel conductor sets (NEC 310.10(G), >= 1/0 AWG) assume identical raceway material, length, and termination geometry for equal current division.
  • Circuit length represents one-way physical route distance; single-phase/DC uses 2× loop factor and balanced three-phase uses √3 line-to-line factor.

Out-of-Scope Boundaries & Required PE Verification

  • NEC 3% branch and 5% total feeder+branch limits are Informational Notes (advisory efficiency/performance recommendations), NOT general mandatory code prohibitions—except for specific articles such as NEC 695.7 (Fire Pumps), 647.4(D) (Sensitive Electronic Equipment), or state energy codes.
  • Steel conduit reactance values slightly overestimate reactance compared to PVC/aluminum raceways; 50 Hz reactance is ~83.3% of 60 Hz Table 9 X.
  • Thermal overload warnings check base 75°C Table 310.16 ampacity at 30°C ambient without conduit bundling derating.

Reference Benchmark & Formula Specification

Deterministic formula
ΔV=K⋅I⋅Lm(R75∘Ccosφ+XLsinφ)1000⋅Nsets\Delta V = \frac{K \cdot I \cdot L_{\text{m}} \left(R_{75^\circ\text{C}}\cos\varphi + X_L\sin\varphi\right)}{1000 \cdot N_{\text{sets}}}K=3(3ϕ),2(1ϕ)K = \sqrt{3}\;\text{(3}\phi\text{)},\; 2\;\text{(1}\phi\text{)}%ΔV=100⋅ΔVVsys\%\Delta V = \frac{100 \cdot \Delta V}{V_{\text{sys}}}
Architecture / Standard Tier Specification Scope / Operating Range Reference Benchmark
NEC 210.19 / NOM-001 Branch Individual Feeder or Branch Run Max Recommended <= 3.0 % 14.4 V max @ 480V
NEC 215.2 Total System Feeder + Branch Combined Max Cumulative <= 5.0 % 24.0 V max @ 480V
IEC 60364-5-52 Lighting Public LV Supply Lighting Max Allowed <= 3.0 % 12.0 V max @ 400V
NEC 647.4 Sensitive Equipment 60/120V Technical Power Strict Mandatory <= 1.5 % 2.0 % Combined Max

Frequently Asked Questions

Should I enter one-way conduit length or round-trip wire length?

Always enter the one-way physical conduit or cable-tray distance from the breaker panel to the load. The formula automatically applies the round-trip factor of 2 for single-phase circuits and √3 (1.732) for balanced three-phase circuits.

Why does aluminum cable require upsizing two AWG gauges vs copper?

AA-8000 series electrical aluminum has roughly 61% of copper's conductivity (~1.64× higher AC resistance per kilometer). Stepping up two AWG trade sizes (for example from 4 AWG copper to 2 AWG aluminum) restores nearly identical voltage drop and 75°C lug ampacity.

Is the NEC 3% voltage drop rule legally mandatory?

In the base NEC 210.19 and 215.2 text, 3%/5% appears as an Informative Note rather than a general mandatory rule—except on fire pumps (NEC 695.7), sensitive electronic power (NEC 647.4), and state energy codes such as ASHRAE 90.1 and California Title 24 where feeder/branch voltage drop limits are strictly enforced.

Related Engineering Calculators & Workbenches

Voltage Drop (V / %) 6.39 V (1.33%)
Inputs ↑